12,900+ practice questions · 144 exams · new questions added every week
Practice questions › Welding inspector › Welding inspection

Welding inspector Welding inspection practice questions

10 free questions with answers and explanations. Try each one, then tap “Show answer”.

  1. Consumables

    1. In the AWS electrode classification E7018, the '70' means

    • A. 70 mm long
    • B. maximum 70 amps
    • C. 70% iron powder
    • D. minimum tensile strength of 70,000 psi
    Show answer

    Answer: D. minimum tensile strength of 70,000 psi

    E7018 is a low-hydrogen electrode.

  2. Documents

    2. Which ASME code section covers welding and brazing qualifications?

    • A. Section IX
    • B. Section V
    • C. Section II
    • D. Section VIII
    Show answer

    Answer: A. Section IX

    Section V covers NDT methods.

  3. Testing

    3. A macro examination of a weld cross-section shows

    • A. fusion, penetration, profile and visible defects
    • B. residual stress
    • C. tensile strength
    • D. chemical composition
    Show answer

    Answer: A. fusion, penetration, profile and visible defects

    It is etched and viewed at low magnification.

  4. Problems

    4. Arc blow is a problem mainly with

    • A. AC welding only
    • B. Brazing
    • C. Oxy-fuel cutting
    • D. DC welding on magnetised material
    Show answer

    Answer: D. DC welding on magnetised material

    Magnetic fields deflect the arc.

  5. Calculations

    5. Calculate the arc energy: 24 V, 200 A, travel speed 250 mm/min. (Arc energy kJ/mm = V × A × 60 ÷ (speed × 1000))

    • A. 1152 kJ/mm
    • B. 11.5 kJ/mm
    • C. 1.15 kJ/mm
    • D. 2.15 kJ/mm
    Show answer

    Answer: C. 1.15 kJ/mm

    24 × 200 × 60 ÷ (250 × 1000) = 1.15 kJ/mm. Heat input = arc energy × process efficiency.

  6. Processes

    6. Which process uses a granular flux blanket and is usually automated?

    • A. Submerged arc welding (SAW)
    • B. MMA
    • C. Oxy-acetylene
    • D. TIG
    Show answer

    Answer: A. Submerged arc welding (SAW)

    The arc is hidden under the flux.

  7. Calculations

    7. An equal-leg mitre fillet weld has a leg length of 14 mm. What is its design throat thickness (approx.)?

    • A. 19.6 mm
    • B. 9.8 mm
    • C. 14 mm
    • D. 7 mm
    Show answer

    Answer: B. 9.8 mm

    Throat ≈ 0.7 × leg = 0.7 × 14 = 9.8 mm.

  8. Testing

    8. A Charpy impact test measures

    • A. hardness
    • B. toughness (energy absorbed at a given temperature)
    • C. tensile strength
    • D. surface finish
    Show answer

    Answer: B. toughness (energy absorbed at a given temperature)

    Results are in joules.

  9. Consumables

    9. Which MMA electrode type is easiest to use and gives a smooth finish for general work?

    • A. Cellulosic
    • B. Basic
    • C. Tungsten
    • D. Rutile
    Show answer

    Answer: D. Rutile

    Basic electrodes are used where low hydrogen is needed.

  10. Positions

    10. In AWS terms, 4G is

    • A. a pipe at 45°
    • B. flat plate
    • C. a groove weld on plate in the overhead position
    • D. vertical plate
    Show answer

    Answer: C. a groove weld on plate in the overhead position

    1G flat, 2G horizontal, 3G vertical, 4G overhead.

Want more Welding inspector Welding inspection questions?

Get fresh questions every day, focused on your weak topics, plus timed mock tests. Free to start.

Practise free in the web app Practise on Telegram

More Welding inspector practice

About the Welding inspector on Mock Night · Original practice questions; not affiliated with the exam board.