12,900+ practice questions · 144 exams · new questions added every week
Practice questions › NDT › Penetrant testing (PT)

NDT Penetrant testing (PT) practice questions

10 free questions with answers and explanations. Try each one, then tap “Show answer”.

  1. Interpretation

    1. Under ASME, a linear indication is one whose length is

    • A. equal to its width
    • B. less than its width
    • C. more than three times its width
    • D. more than 1 mm only
    Show answer

    Answer: C. more than three times its width

    Otherwise it is a rounded indication.

  2. Cleaning

    2. Vapour degreasing and solvent cleaning before PT are used to remove

    • A. magnetism
    • B. the base metal
    • C. fluorescence
    • D. oils and greases
    Show answer

    Answer: D. oils and greases

    Contaminants stop penetrant entering defects.

  3. Process

    3. Low part temperatures generally require

    • A. no developer
    • B. a longer penetrant dwell time
    • C. a shorter dwell time
    • D. fluorescent light only
    Show answer

    Answer: B. a longer penetrant dwell time

    Penetrant becomes more viscous when cold.

  4. Materials

    4. Fluorescent penetrant sensitivity levels run from ½ (lowest) to

    • A. 100
    • B. 2
    • C. 10
    • D. 4 (ultra-high)
    Show answer

    Answer: D. 4 (ultra-high)

    Higher levels find finer cracks.

  5. Types

    5. Which type of penetrant is generally more sensitive?

    • A. Fluorescent
    • B. Visible (red)
    • C. Neither can find cracks
    • D. Both are identical
    Show answer

    Answer: A. Fluorescent

    Fluorescent indications glow under UV-A light.

  6. Principles

    6. Penetrant testing relies mainly on

    • A. sound reflection
    • B. capillary action
    • C. X-ray absorption
    • D. magnetism
    Show answer

    Answer: B. capillary action

    The penetrant is drawn into surface-breaking openings.

  7. Process

    7. Under ASME Section V, the standard temperature range for PT is

    • A. 20 °C to 30 °C only
    • B. 0 °C to 100 °C
    • C. -10 °C to 40 °C
    • D. 10 °C to 52 °C
    Show answer

    Answer: D. 10 °C to 52 °C

    Outside this range the procedure must be qualified.

  8. Materials

    8. A lipophilic emulsifier is

    • A. oil-based and applied after the penetrant dwell
    • B. a cleaner used before penetrant
    • C. a developer
    • D. water-based remover
    Show answer

    Answer: A. oil-based and applied after the penetrant dwell

    Hydrophilic removers are water-based.

  9. Materials

    9. With post-emulsifiable penetrants, which time is most critical to control?

    • A. Time to read the procedure
    • B. Shelf life of the developer
    • C. Emulsification time
    • D. Drying time of the cleaner
    Show answer

    Answer: C. Emulsification time

    Too long and penetrant is removed from defects.

  10. Process

    10. If a part must be re-inspected, it should be

    • A. wiped and inspected again
    • B. magnetised
    • C. fully cleaned and processed again from the start
    • D. just given more developer
    Show answer

    Answer: C. fully cleaned and processed again from the start

    Old penetrant in defects can give unreliable results.

Want more NDT Penetrant testing (PT) questions?

Get fresh questions every day, focused on your weak topics, plus timed mock tests. Free to start.

Practise free in the web app Practise on Telegram

More NDT practice

About the NDT on Mock Night · Original practice questions; not affiliated with the exam board.