12,900+ practice questions · 144 exams · new questions added every week
Practice questions › NDT › Ultrasonic testing (UT)

NDT Ultrasonic testing (UT) practice questions

10 free questions with answers and explanations. Try each one, then tap “Show answer”.

  1. Calculations

    1. Estimate the near field length of a 10 mm diameter, 5 MHz probe in steel (longitudinal, 5,920 m/s). (N = D²f ÷ 4v)

    • A. 21.1 mm
    • B. 84.5 mm
    • C. 10.6 mm
    • D. 2.1 mm
    Show answer

    Answer: A. 21.1 mm

    N = 10² × 5 MHz ÷ (4 × 5.92 mm/µs) = 21.1 mm.

  2. Calculations

    2. A Perspex wedge (2,730 m/s) has an incident angle of 35°. What is the refracted shear-wave angle in steel (3,240 m/s)? (sin θ₂ = sin θ₁ × V₂ ÷ V₁)

    • A. 35°
    • B. 53°
    • C. 29°
    • D. 43°
    Show answer

    Answer: D. 43°

    sin θ₂ = sin 35° × 3240 ÷ 2730 = 0.681, so θ₂ ≈ 43°.

  3. Principles

    3. Which law describes refraction of sound at an interface?

    • A. Ohm's law
    • B. The inverse square law
    • C. Snell's law
    • D. Hooke's law
    Show answer

    Answer: C. Snell's law

    It links angles to the velocities in each material.

  4. Calculations

    4. A longitudinal-wave probe on steel (velocity 5,920 m/s) shows a back-wall echo at 2.5 µs (round trip). What is the thickness?

    • A. 4.1 mm
    • B. 14.8 mm
    • C. 7.4 mm
    • D. 11.1 mm
    Show answer

    Answer: C. 7.4 mm

    Thickness = velocity × time ÷ 2 = 5.92 mm/µs × 2.5 µs ÷ 2 = 7.4 mm (the sound travels there and back).

  5. Technique

    5. Time-corrected gain (TCG) and DAC both

    • A. compensate for loss of amplitude with distance
    • B. magnetise the part
    • C. remove the near field
    • D. replace calibration
    Show answer

    Answer: A. compensate for loss of amplitude with distance

    TCG adjusts gain electronically instead of drawing a curve.

  6. Principles

    6. Acoustic impedance is

    • A. voltage × current
    • B. density × sound velocity
    • C. frequency × wavelength
    • D. thickness ÷ time
    Show answer

    Answer: B. density × sound velocity

    Large impedance differences cause strong reflections.

  7. Principles

    7. Beam spread increases when

    • A. frequency is lower or the probe is smaller
    • B. more couplant is used
    • C. the probe is larger
    • D. frequency is higher
    Show answer

    Answer: A. frequency is lower or the probe is smaller

    Higher frequency and larger probes give a tighter beam.

  8. Calculations

    8. One echo is 4 times the amplitude of another. What is the difference in dB? (dB = 20 log₁₀ ratio)

    • A. 6 dB
    • B. -12 dB
    • C. 24 dB
    • D. 12 dB
    Show answer

    Answer: D. 12 dB

    20 × log₁₀(4) = 12 dB.

  9. Principles

    9. Increasing probe frequency generally gives

    • A. better resolution but less penetration
    • B. more penetration and better resolution
    • C. more penetration and worse resolution
    • D. no change
    Show answer

    Answer: A. better resolution but less penetration

    Lower frequencies penetrate coarse-grained material better.

  10. Principles

    10. The region close to the probe where signals are unreliable because of interference is the

    • A. near field (Fresnel zone)
    • B. dead zone of the material
    • C. HAZ
    • D. far field
    Show answer

    Answer: A. near field (Fresnel zone)

    Beyond it is the far field (Fraunhofer zone).

Want more NDT Ultrasonic testing (UT) questions?

Get fresh questions every day, focused on your weak topics, plus timed mock tests. Free to start.

Practise free in the web app Practise on Telegram

More NDT practice

About the NDT on Mock Night · Original practice questions; not affiliated with the exam board.